ASTM D is a test method used to study the apparent tensile strength of plastic pipes using a specialized test fixture. The ASTM D standard determines the comparative apparent tensile strength of most plastic products using a split disk test fixture tested under defined. ASTM D TESTING FIXTURE. Split disk and ring segment tensile tests, properly interpreted, provide reasonably accurate information with regard to.

Author: JoJorisar Gom
Country: Sierra Leone
Language: English (Spanish)
Genre: Video
Published (Last): 9 September 2005
Pages: 147
PDF File Size: 11.83 Mb
ePub File Size: 14.31 Mb
ISBN: 532-6-59041-995-7
Downloads: 19570
Price: Free* [*Free Regsitration Required]
Uploader: Arashijora

Astm d2290 is the responsibility of the user of this standard astm d2290 establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The ASTM D standard determines the comparative apparent tensile strength of most plastic products using astm d2290 split disk test fixture tested under defined conditions and test machine speed.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Force range of 5 kN to kN 1, lbf tolbf Adjustable test space The most popular choice for static tension and compression tests These dual column testers are available in both tabletop and floor standing models. In general, this test astm d2290 is still generally considered an acceptable test for unidirectional hoop-wound composite rings.

Although this original Procedure A test method was an ASTM standard from astm d2290its popularity has varied over the years.

Have a question about conducting the test for this standard? Work Item s – proposed revisions of this standard.


Data from this test are useful for research and development, quality control specification and design. Rather than testing a complete ring, two 4″ long segments of the ring are tested together in a special astm d2290 fully defined astm d2290 ASTM D Procedure E is used for polyvinyl chloride PVC pipe with a nominal diameter of 14 in.


Within limits, specimens of varying sizes can be tested using the same holders, by using interchangeable pairs of split disks. These former Procedure A specimens are hoop-wound rings astm d2290 controlled diameter, astm d2290, and thickness, viz.

Historical Version s – view previous versions of standard.

ASTM D2290 Plastic Pipe Hoop Tensile Strength Testing

Wyoming Test Fixtures Inc. By means of our plastic testing expertise and modular product design, we will help find the testing solution that is right for you. This test method also is applicable to extruded and molded thermoplastic pipe. The original fixture for testing Procedure A specimens, i. Sources of Additional Information: Give one of our application engineers a call today for help with creating the best budget and testing plan according to ASTM D These effects are discussed in References 3 and 4.

We are confident that we have what you are looking for. Procedure C has been used on polyethylene and polybutylene pipe to produce results equivalent to Quick Burst results Test Method D for 4 in. This test method astm d2290 applicable to reinforced-thermosetting resin pipe regardless of fabrication method.

The original Procedure B and C specimens, extruded and molded unreinforced astm d2290 specimens astm d2290 larger diameter extruded plastic pipe, respectively, utilized fixtures of astm d2290 general type shown at the right side of Fig. However, this now deleted original Procedure A fixture, while astm d2290 longer an ASTM standard, is still used for testing filament-wound composite rings, and the fixture is available from Wyoming Test Fixtures, Inc.

The test cannot be considered significant for applications differing widely from the load-time scale of the standard test.

All of these revised procedures use the same general astm d2290 configuration the configuration astm d2290 on the right side of Fig. Procedure D is used for polyethylene pipe with a nominal diameter of 14 in.

Most Related  PUBLIC LAW 73-10 PDF

The version of ASTM D has added a Procedure D, for testing astm d2290 pipe with a nominal diameter of 14″ astm d2290 greater and preferably having a wall thickness 1″ and greater. These various specimen configurations and test procedures are fully defined in the version of ASTM D Reference 1. Friction between the split disk fixture and the ring specimen is also a concern.

This potential error is analyzed and discussed in detail in References 2 and 3. Reinforced thermosetting resin pipe may be tested by this standard regardless of fabrication method. Procedure A is now used for testing reinforced-thermosetting resin pipe, Procedure B for thermoplastic pipe of any size, and Procedure C for thermoplastic pipe with nominal diameters of 4. Details of the now obsolete fixture and specimen for testing filament-wound rings can be found can be found in and earlier versions of ASTM D Extruded and molded thermoplastic piping is also covered by this test.

Link to Active This link will always route astm d2290 the astm d2290 Active version astm d2290 the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

We offer astm d2290, apparatus, testers, tensile grips, test fixtures, clamps, holders, jigs, faces, jaws, extensometers, environmental and humidity chambers, furnaces, baths and custom solutions for unique applications. One criticism is astm d2290 some bending is induced in the ring specimen at the split.